一、主要参数: Main Technical Parameter 1.设计速度:200米/分钟。 Designed production speed:200m/min 2.生产速度:120-150米/分 Stable production speed:120-150m/min 3. 电源:380v ,50Hz Machine power: 380v ,50Hz 4.装机容量:300 kw(不含胶机机功率)。(暂定) Machine capacity: 300 kw(excluding the glue applicator power). 5.次品率:≤ 3%kw Wasted products rate: ≤ 3%kw 6.产品规格:有S,M,L,XL四种规格。 Product specification: S, M, L, XL 7.设备尺寸(不含粉碎机,堆垛机,风机) Overall size (excluding crusher ,stackerfan) 二、基本配置 Basic Assembling Unit 1. 两台齿片式粉碎机,可破碎未处理桨,半处理浆和处理浆,进给量在触摸屏上设定。加装隔音房。 Two teeth-like crusher can take treateduntreated pulp. The amount of wood pulp designed on the touch-screen. Equipped with soundproof room. 2. 工字型模轮。 工type mould wheel. 3. 木桨进给量在触摸屏上设定. The amount of the wood pulp designed on the touch-screen. 4. 高分子与木浆混合,进给量在触摸屏上设定。 SPA mixed together with wood pulp, the amount can be designed on the touch-screen. 5. 棉芯压花,花型通用为网格,可以按客户花型定制。 Cotton core with embossment, generally the embossment pattern are net type,also it can be designed as the customers request. 6. 加衬导流无纺布装置。 Add lead-flow N.W fabric unit. 7. 棉芯用切切断。 Use the cutting knife cut the cotton core. 8. 弹性腰围装置,弹性腰围长度腰帖长度触摸屏上设定。 Elastic waistline unit, the length can be designed by touch-screen. 9. 立体护围制作装置.热压方式. Protection-leakage unit. Heat-press type. 10. 左右腰贴施加装置,电子凸轮控制.腰贴长度触摸屏上设定. Side sticker are added on the machine, electric protrusive wheel control. The length of the side sticker can be designed on the touch-screen. 11. 前腰帖装置电子凸轮控制。可以在线刮(喷)胶。前腰帖长度腰帖长度触摸屏上设定。 Frontal sticker unit controlled by electric protrusive wheel. The length of the side sticker can be designed on the touch-screen. 12. 莱卡橡胶开卷装置,其中棉芯两侧歌配3-4条橡筋,立体护围2-4 LaiKa rubber roll unit, sides of the cotton core equipped with 3-4 rubber stripes. 2-4 sides of leakage-barrier products with two rubber stripes. The extentive power can be designed on the touch-screen. 13. 产品切弧边装置。 The product cuts nearby the arc to install. 14. 产品纵向折叠,压实后切断成型。 The product longitudinal folds, the post-compaction shuts off takes shape. 15. 产品横向三折或二折。 Product crosswise three-foldedtwo-folded. 16. 整机采用日本三菱伺服控制系统。更换规格时仅需更换弧切装置。其余更改在触摸屏上完成. Entire machine uses the Japanese Mitsubishi servocontrol. When replacement specification only must replace the arc to cut the installment. Other changes in touches on the screen to complete. 17. 产品整列输出。 The product falls in the output. 18. 配急停索。 Matches stops the rope anxiously. 19. 配电动葫芦。 Matches the electric hoist. 20. 配落地式安全防护门。 Matches the console-model safe protection gate. 21. 配操作楼层架。 Matches the operation floor frame. 22. 配集尘系统。 Matches the dust-collecting system.